1) The stratum has a long depositional age, and the stratum has high hardness and inhomogeneity, and some sections have high abrasiveness.
The Ziliujing group with a thickness of more than 500m, mud shale, sandstone interbedded, sand and mudstone compact and high hardness. The drillability grade is 4.7-7.5, and the rock hardness varies greatly. Due to the high confining pressure, the hardness of the Permian limestone is more than 3 times higher than that of the Triassic, and the central zone has flint nodules, coal and pyrite.
2) The wellbore is unstable.
The Shaximiao Formation-Zhenzhuchong Formation in the upper part of the high and steep structural well in eastern Sichuan (well depth 0-2500m) is mainly composed of interbedded sand, mud and shale. Due to the strong water sensitivity of the rock and the combined action of the in-situ stress of the high and steep structures, the wellbore is easily destabilized and the wellbore collapses severely. In order to balance the collapse, the drilling fluid density was increased, resulting in a significant reduction in the ROP. For example, the drilling fluid density in Well Tiandong 26 was raised to 1.35-1.63 g/cm3 in the Shaximiao and Ziliu formations, which is caused by the high liquid column pressure. The "squeezing effect" caused the ROP to drop to 0.96m/h; the Permian Longtan Formation and Liangshan Formation are also prone to collapse.
3) The formation dip angle is large, the formation dip angle is 8 to 55°, and the maximum is 85°, which is prone to natural formation deflection.
In order to control the well deviation, the measures of light pressure and hoisting are often adopted, which greatly reduces the drilling speed.
4) The formation pressure system is complex, interlaced from negative pressure to abnormal high pressure, with the diversity of the vertical pressure system and the relative independence of the horizontal pressure system.
Carbonate gas reservoirs have three types of production layers: fracture, porosity and fracture-porosity. Porous gas reservoirs have clear pressure regularity and are basically normal pressure, which can realize balanced drilling, such as Carboniferous and Changxing reefs in eastern Sichuan. However, the fractured gas layer pressure depends on the strength of the geological movement and the strength and regularity of the rock itself, so it is difficult to predict. When drilling, high-density drilling fluid is used to drill according to the existence of cracks. This leads to overbalance and affects the ROP. However, if low-density drilling fluid is used for fast and strong drilling, the risk of sudden fracture and blowout is very high. In the two high-pressure production layers of Yangxin Formation and Changxing Formation, due to high pressure gradient, high rock hardness, and deep formation depth, the drilling fluid density is usually 1.50g/cm3; (the highest pressure gradient in Well Yunan 6 reaches 2.45MPa/hm, drilling The liquid density is 2.41g/cm3), resulting in the drilling speed hovering around 1.00m/h for a long time.
5) Large size wellbore is long.
The section of the wellbore larger than 311.1mm in the eastern Sichuan area accounts for about 1/2 to 3/4 of the total footage, and the WOB cannot be increased due to the well deviation factor. The drilling pressure of the in head can only be increased to 120 ~ 180kN, and the speed is generally 60r/min. Large-sized wellbore bits have large rock-breaking volume. For example, the rock-breaking volume of the in-bit bit is 4.24 times that of the 8Min bit, and the rock-breaking volume of the in-bit bit is 2.08 times that of the in-bit bit. Obviously, the mechanical rock-breaking energy of the drill bit at the bottom of the well is seriously insufficient, and it is difficult for the teeth to penetrate into the formation. The rock-breaking method is mainly based on grinding, rather than volume breaking, resulting in low rock-breaking efficiency of the drill bit. Due to the large size and depth of the wellbore, the actual annulus return velocity is below 0.8m/s, and the hydraulic energy is also seriously insufficient, resulting in poor bottom hole cleaning effect and repeated breaking of cuttings. The deepening of the segment. The jumping phenomenon of the roller cone bit is particularly prominent. The effective drilling time of the bit at the bottom of the hole is less than 50%, which also seriously affects the improvement of the ROP.





